Homemade blackcurrant brandy...

One of the many things we do in preparation for Christmas (and winter) is to make liqueurs, we normally use our homegrown blackcurrants or blackberries (we're doing both this year) we pick from the hedgerows, either way the method is the same, basically it's infusing a spirit (brandy in this case) with the flavour of a fruit of some kind, the same way sloe gin is made, we're just not big gin drinkers so this is a good replacement for gin, many different spirits can be used, vodka being one of them.

It takes a few minutes to prepare then it can be left alone for a couple of months, once it's ready it takes a few minutes to strain the fruit out and bottle, if you start this a few months before christmas you'll have a nice warming winter drink for very little effort and money.

Thanks for visiting.

Spinning christmas tree ornament ... ...

Just a short post on another of our christmas creations, at this rate we will have more or less refitted the tree in handmade decorations.

Here it is.

My wife had mentioned making tree decorations like the one above out of some foam sheet we have, but after looking at the thickness of the foam we decided it wouldn't work very well.

So this afternoon I set about making one out of wood.

They are simple enough to make, you need a few tools though, mainly a saw of some kind (a small hacksaw, or coping saw will do) and a thin drill bit and drill (a 2mm drill bit) all you have to do is mark out your shape on some wood (I used a scrap piece of 10mm tongue and grove) I've chosen a tree shape, but you could do a snowman, or a circular decoration, you could also use a star shape and instead of slicing it like I have you could cut a series of stars out of the main one, so that they all spin inside each other (I'll most likely write a post about it at some point)

Once you have marked your shape out you need to divide it into equal sections, I made my sections about 10mm (1cm) thick, then mark the centre of your shape, this makes it easier to align the holes you will drill through each section.

A closer up picture - 

It's not really wonky, it's the camera angle ;-)

Use the saw to slice up your shape, try and keep the pieces in the order your saw them (although with a simple shape it's easy to figure out where the bits go) then take each piece and drill a hole in the middle (use the centre line you made as a guide) do this for all the parts, if you use wood you may want to give each part a sand after you've cut and drilled them for a smoother look.

Then the fun bit, you can use thin gauge wire,string,wool or cotton thread for this part, you'll need some small beads or something to put between each section as well.

I used a larger bead at the bottom of the tree, but one the same size as the others would do, you could also use a small bell for extra jingle. Thread your chosen material through each part, you can use the first bead/bell to tie the string or wire to, so it doesn't all slide off.

After each section add a bead, then another section, then a bead and so on, until you get to the top, at this point you can either use the last section, or use a large bead, or bell or maybe if you have some star shaped beads you could use them, that's the beauty of crafts, you can do what ever you feel like, it's about imagination. Then just leave a loop to hang it on the tree with.

Here it is again, in case you missed it at the start of the post ;-)

It doesn't take long to do, and you can get the kids involved, although you may want to do the sawing or cutting, then you can decorate them however you want, I've used some silver spray and a little glitter spray, you can use glue and glitter or anything else you have.

You don't need to use wood either, some thick cardboard would work just as well, and if you don't have a saw this may be a better option, it should work in the same way.

And there you have it, a spinning christmas tree decoration.

Thanks for reading.

A star is born ... ...

Instead of buying a load of new christmas decorations this year we have been making our own, we have made them out of paper,pine cones,card and for the stars below wire and string, much more fun than fighting through shops looking for decorations that probably won't last half as long, it's good for the kids to do some christmas crafts as well.

Here's the stars -

They may not be to every one's taste.

The colour of the silver spray didn't really come out in the picture, they are easy enough to make, all you need is some wire (I used gardening wire) and some string, any string will do, or wool. You can also make them from string instead of wire, but it's a little harder to keep it altogether, you can spray them what ever colour you like, we used silver and some glitter spray, you can use gold as well.

Making them doesn't take long, although if you spray them you will need to wait a short while for the paint to dry. If you use wire you will need a jig (no fiddles involved) to make the basic star shape, unless of course you feel like making them free hand.

To make the jig you'll need some nails, a piece of wood, a hammer and a template, which you can either print out from your pc or draw on a bit of paper, then all you do is place the paper onto the wood and hammer nails into it at all the angles of your shape.

The jig with nails already hammered in - 

It should look something like this.

It makes it a lot easier to bend the wire into shape using a jig. Next take a piece of string and wind it round all the nails to make a star, basically you use the string to measure how much wire you will need, you want to leave a little extra wire so you can twist it together.

Using the string to measure - 

Measuring done.

Time to get some wire, you can see that I've used slightly more string than is needed, this will make it easier to fix the wire together. Next get your wire and use the string to measure out a length of it, then cut it (I should have mentioned that you may need wire cutters, or pliers) then all you need to do is wind the wire around the nails in the same way you did the string, thinner wire will bend easier, I got ours from the garden section at b&q.

Once that's done twist the wire together where the two ends join, again pliers will do the job, depending on how thick the wire is, then all that's left is to wind your string of choice around the wire frame, when you are happy with it, either tie the string to the frame and cut off any extra, or you can use a spot of glue to fix it. 

You don't have to spray them, you could use paints from a pot, get the kids to do it or you could just cover them in glue and glitter or anything else that you feel like really, it's up to you.

A close up - 

Still didn't manage to get the glitter to show, it's there I promise.

And that's it, they may not be flashy shiny plastic type shop bought ones, but to be honest I think they look better, and they'll last for a while, and even if you don't want to hang them on your tree if you got the kids to decorate them they will have had a great time, and that's what it's all about, and you don't have to make stars, why not try different shapes ? like snowmen or christmas trees ?

Thanks for reading.