From Ash Trays To Pin Cushions...

It's always good when you can find a purpose for an old item, it gives it a new life and saves it from the bin, which is I think anyway something we should do more of, it's not a new thing either, people have been changing things from their original purpose for many years, we tend to call it being thrifty or frugal these days, but it's not new but it is a good idea, it saves things from landfill, it save you money.

So here's something I recently gave a new life to - 

Not that useful these days.

A pair? of small brass shoe shaped ash trays with some nice engraving, they've had some colour added to the inlay as well, they are quite nice and obviously served a specific function, but these days fewer people smoke which isn't a bad thing, but what to do with a couple of old ash trays?

My first thought was pin cushions, my reasoning was that they are small and have a novelty value which is probably why they were ash trays in the first place.

To turn them into pin cushions was easy enough, all I did was get rid of the section on the back that would have held the cigarette, as these are brass I had to use my multi-tool.

Ready for modification - 

Time for some surgery.

It didn't take long to grind away the back section, I used a small sanding attachment to remove any sharp edges and that was it basically, the next step is make a cushion.

Ready for a cushion.

The cushion was made from some old red velvet as it goes well with the brass (better once the brass was polished) and stuffed it with some wadding from an old pillow, I haven't detailed the steps, but basically I stitched a sausage shape from the velvet and stuffed it with wadding, then it was glued into the shoe.

And this is what I ended up with -

I'm pleased with them.

So there we have it, a pair of quirky pin cushions, a good size for a sewing box or bag and a good use of old objects that don't really have a purpose anymore.

Thanks for visiting.

New life into an old box...

I thought it was about time I wrote a post, so here it is and as the title says I'm breathing new life into an old box, an old work box / sewing box to be precise.

Now some people will says that old pieces of furniture like this should be left as they are, and for the most part I agree but not always.

Here's the work box - 

It is a nice little work box on barley twist legs, has the added bonus of a storage drawer and a second shelf so it's useful and structurally sound although old rickety joints are easy enough to fix.

The finish or rather whats left of it is not so good, so it needs removing, which is what I'd just started to do in the picture above.

Before that I took out the old lining, now some will say I should have left it and had it been in in good condition I might have, however it had some staining same goes for the drawer lining, it also had an aroma of old so it had to go.

Removing the lining - 

Was probably quite nice in its day.

The lining came out easily enough, although it did leave some of the old card backing in place so to remove that I used a bit of warm soapy water and a scraper much in the way you do when removing wallpaper, so basically wet the card and scrape off.

Like so - 

It's a bit sticky.

The glue used can get a little slimy and sticky but I've found that it will wash off with soap and water and once done you're left with clean wood, which can be sanded and stained, or re-covered.

I also took out some of the woodwork as it needed replacing because I removed the lining.

Wood out - 

Was never meant to be seen, so they cut costs and used what they had.

With the clean up done it was basically sanding and a fair bit of it, which I did by hand and not using a powered sander the main reason is that over the years I've found the types of finishes used in the early part of the 20th century (which when the box dates to) kind of heat up with the friction of an orbital sander and once they do they clog the sanding pads quite quickly, so I just used some 80grit sandpaper and a cork block, it didn't take long and saved on materials, I could have used a chemical stripper but I try to avoid those where possible.

Top sanded back to bare wood - 

Roughly 10 minutes work.

Sanding revealed a lovely oak top, most likely quarter sawn oak, once the top was done it was just more of the same, so I started with 80grit going with the grain and once it was done I used 120grit and once I was happy it was pretty much done.

All sanded - 

Ready for some wax.

The only repair needed was replacing the wood divider that sits between the bottom of the box and drawer, I used a thin piece of reclaimed oak for that.

And it's all done -

Ready for a new life somewhere.

Once I'd sanded it I wiped it over to clean the wood and then I waxed it with an oak coloured wax which once dry I buffed to a shine, then I coated it with a clear wax and again buffed it to a shine, overall I'm pleased with the results and the box is ready to live on, it is still a useful and compact piece of furniture, some people may say it's not fashionable, it's brown furniture I disagree.

It's a lovely antique oak work box that belongs in a nice room in a house and not in the bin or on a bonfire.

Thanks for visiting.

Up-cycling an old shoe shine box...

A short video where I up-cycle an old shoe shine box into something more useful, in this case an easy to carry sewing box.

The box didn't really need much doing to it, just a new handle and a bit of sanding, I did make a small tray for the inside to add extra storage, all in all I'm happy with the results, and again another object given a new life and saved from the bin and for no cost other than a little effort.

I've found over the years that although an object might need some work the way it was built is much better than modern equivalents and was made from better materials, I guess more effort was put in to making an item that functioned well but would also last for many years and production costs were less of an issue.

Anyway the video is below.

Thanks for visiting.