Friday, 19 August 2016

Homemade moth trap...

We like to spend a lot of time in and around all things nature, be it the local woods (we have a few) the beach and anywhere in between and one of the things we like to look at are moths, the problem however is that most moths (not all) fly at night so we usually try to attract some using a sheet and a light, this doesn't always have a lot of success, so we built an upgrade.

Here's the old sheet and light bulb (it's not the best, but it does work) -

Doesn't get anymore basic.
What we've done is to build what is known as a 'Skinner moth trap' you can buy these and various other types of trap, but we managed to knock one up using things we had lying about, so our cost nothing, not a single penny (to build anyway) it's basic so can be built easily no matter what diy skills you may or may not have.

Here's the finished trap set up and waiting for it to get dark - 

Basic indeed, why the egg boxes? read on.

It's basically a wooden box, in our case made from what was left of our daughters old wardrobe, we've recently (after three years of looking) bought her an old antique one, this seemed as good a way as any of recycling the old one.

The glass was from an old fish tank which I broke, most traps of this type use perspex, but we were building it as cheaply as possible, and the glass is toughened which is handy.

The bulb holder and wire I had lying about in the shed and the bulb is just an energy saving one, you can however buy lighting kits (that use mercury vapour bulbs) online specifically designed for fitting to your own moth traps, these can be pricey though, but may yield better results.

Sides roughly marked up - 

The diagonal lines are where the glass will go.

All you need to do is make a box with four sides and a base, we had to make this to a set size because of the glass, so we went with a box just wide enough to fit the glass in, if you use perspex you can always cut it to size.

The glass just sits at a 45 degree angle (roughly) so all that you need to add to the box is a couple of wooden blocks to stop the glass falling into it and to create a gap at the bottom, so it's basically a funnel, the idea being the moths will see the light and then fall into to the trap.

Wooden stoppers to hold the glass - 

Rough, but they work.

Stoppers and glass in place - 

Just needs a base.

For the light I used a random fitting I had lying about, this I fixed to a wooden bar that runs across the trap, it also acts as a carrying handle, the flex for the light runs under the bar and over the side.

Fitting the light - 

You can see where the glass stops a little clearer.

Testing, testing - 

Let there be light.

And that was it, as I said it's basic and as it's hobbled together from essentially scrap material it cost nothing, the only other you'll need is some egg boxes to put inside it, this gives the moths good places to hide, we did also fix a black umbrella to one side of the trap, this was to diffuse the light shining into windows as we didn't want to upset the neighbours.

I haven't put sizes because I worked to the glass sheets I had, and if you're not confident with wiring then you can either buy a kit or you can buy clip on light fittings so all you'll need is a bulb, we used a low energy bulb mainly because they are cheap to run, and they aren't as bright as incandescent ones.

Did it work ? well yes, although we didn't catch much, but weather conditions may have been a factor and we do have a lot of bats that fly over the garden, that and the fact that dad accidentally let the ones in the trap go before we got a good look at them, but we did manage to get a picture of one moth we caught.

Here it is, it's one we haven't seen before - 

Ennomos alniaria - Canary-shouldered Thorn moth.

If you don't fancy building a moth trap you can try baiting (sugaring) guides can be found online, lots of flowering plants in your garden will also attract moths, moths are pollinators, we usually get loads on our buddleia plants (especially the white ones) and failing that keep an eye out for caterpillars roaming about, you can take them home and watch them change or let them go we currently have two large species in the pupal stage.

Lasiocampa quercus - Oak Eggar moth.

Caterpillar - 

Fuzzy.

Pupal stage - 

Cocoon also fuzzy.

Mimas tiliae - Lime Hawk moth.

Caterpillar - 

Kind of sausage like.

Pupal stage - 

The dried up thing on the left is what's left once it turns into a chrysalis.

I wrote a post a few years back on 'The Humble moth'  there are pictures of a Lime hawk moth we hatched out, along with an Angle shade moth in that post.

And if you do find any bugs and you're not sure what it might be then uksafari is a good site for identifying bugs of all kinds and for moths specifically we've found this site useful Ukmoths

We will be putting the trap out again soon, which is the good thing about it, it's easy to set up and leave for a few hours, just bare in mind that the lights are bright but you can shield the light easily with a sheet or put the trap at the bottom of the garden so as to not upset your neighbours.

And always let the moths go when you're finished looking at them, it's also advisable to not use the trap two or more days in a row, leave it a good few days between using it.

Thanks for reading.

Wednesday, 17 August 2016

Turning captive rings...

lately I've decided I should have a go at turning some pieces with captive rings, the only problem was I don't have a tool for turning captive rings, so I made a rough one from an old chisel, and one from an allen key.


Here's a goblet I made with a captive ring -

This was my third attempt at a captive ring.
Technically you don't need a special tool (which can be quite pricey) for turning captive rings, you can make one quite easily and if you look online you can find numerous different ways of making tools that will do the job.

I made mine from an old wood chisel which cost £1, all I've done is to sort of mimic the way a captive ring tool looks, which is kind of like a chisel with a hole drilled into it.

Here's my cheap chisel - 

Now for a bit of shaping.

To get the shape all I did was ground out a hole into the end of the chisel using a small grinding bit in my multi-tool and created a kind of hook shape.

One captive ring tool - 

Didn't take long to do.

And that's about it, now it's not perfect and needs some tweaking but I am able to turn things with captive rings quite easily all be it small pieces, for larger pieces it's just as easy to use a small gouge as you have more room to work.

Here's what I meant about it not being perfect, it's not sharp enough - 

The inside is very rough.

As you can see it leaves quite a ragged inside to the ring, and as I've discovered it's not that easy sanding the inside of the rings, at least not on small pieces.

The other thing I've tried is grinding the short end of an allen key to give is sharp edges and using that held in a chuck with a handle, this so far is much better as I can get right behind the ring, even on small pieces and I'm able to get much sharper edges on the allen key than I can with the modified chisel, probably due to the steel being better.

Here's one of my holders made from an old hand drill chuck - 

Quite versatile as it happens.

Here's a goblet I made using an allen key held in a chuck to make the rings - 

A vast improvement on others I've made.

So far I've made seven pieces with captive rings (and I need more practice) the latest being a fairly large goblet with two rings made from a piece of ash I chose for it's cracks and imperfections, you can watch the short video (about nine minutes, no sound) of me at various stages of turning, or if not just skip to the end of this post for the picture.

Video - 




Finished goblet - 

I'm pleased with it.
It's not the best way of doing things, but it works for me and it's something I intend to tweak and make better, it's always worth seeing if you can make your own tools, shop bought turning tools can be expensive and more often than not you can make something that works just as well for a lot less and I feel it gives you a better understanding of how things work.

Thanks for reading.


Wedding ring modification...

Like a lot of married people I wear a wedding ring, and if you've ever worn a ring you'll know that whilst it might have been a goo...